Section (4) rtc

Linux manual pages Section 4  


rtc — real-time clock


#include <linux/rtc.h>
int ioctl( fd,


This is the interface to drivers for real-time clocks (RTCs).

Most computers have one or more hardware clocks which record the current wall clock time. These are called Real Time Clocks (RTCs). One of these usually has battery backup power so that it tracks the time even while the computer is turned off. RTCs often provide alarms and other interrupts.

All i386 PCs, and ACPI-based systems, have an RTC that is compatible with the Motorola MC146818 chip on the original PC/AT. Today such an RTC is usually integrated into the mainboard_zsingle_quotesz_s chipset (south bridge), and uses a replaceable coin-sized backup battery.

Non-PC systems, such as embedded systems built around system-on-chip processors, use other implementations. They usually won_zsingle_quotesz_t offer the same functionality as the RTC from a PC/AT.

RTC vs system clock

RTCs should not be confused with the system clock, which is a software clock maintained by the kernel and used to implement gettimeofday(2) and time(2), as well as setting timestamps on files, and so on. The system clock reports seconds and microseconds since a start point, defined to be the POSIX Epoch: 1970-01-01 00:00:00 +0000 (UTC). (One common implementation counts timer interrupts, once per jiffy, at a frequency of 100, 250, or 1000 Hz.) That is, it is supposed to report wall clock time, which RTCs also do.

A key difference between an RTC and the system clock is that RTCs run even when the system is in a low power state (including off), and the system clock can_zsingle_quotesz_t. Until it is initialized, the system clock can only report time since system boot ... not since the POSIX Epoch. So at boot time, and after resuming from a system low power state, the system clock will often be set to the current wall clock time using an RTC. Systems without an RTC need to set the system clock using another clock, maybe across the network or by entering that data manually.

RTC functionality

RTCs can be read and written with hwclock(8), or directly with the ioctl requests listed below.

Besides tracking the date and time, many RTCs can also generate interrupts

  • on every clock update (i.e., once per second);

  • at periodic intervals with a frequency that can be set to any power-of-2 multiple in the range 2 Hz to 8192 Hz;

  • on reaching a previously specified alarm time.

Each of those interrupt sources can be enabled or disabled separately. On many systems, the alarm interrupt can be configured as a system wakeup event, which can resume the system from a low power state such as Suspend-to-RAM (STR, called S3 in ACPI systems), Hibernation (called S4 in ACPI systems), or even off (called S5 in ACPI systems). On some systems, the battery backed RTC can_zsingle_quotesz_t issue interrupts, but another one can.

The /dev/rtc (or /dev/rtc0, /dev/rtc1, etc.) device can be opened only once (until it is closed) and it is read-only. On read(2) and select(2) the calling process is blocked until the next interrupt from that RTC is received. Following the interrupt, the process can read a long integer, of which the least significant byte contains a bit mask encoding the types of interrupt that occurred, while the remaining 3 bytes contain the number of interrupts since the last read(2).

ioctl(2) interface

The following ioctl(2) requests are defined on file descriptors connected to RTC devices:


Returns this RTC_zsingle_quotesz_s time in the following structure:

struct rtc_time {
  int   tm_sec;  
  int   tm_min;  
  int   tm_hour;  
  int   tm_mday;  
  int   tm_mon;  
  int   tm_year;  
  int   tm_wday;
/* unused */
  int   tm_yday;
/* unused */
  int   tm_isdst;
/* unused */

The fields in this structure have the same meaning and ranges as for the tm structure described in gmtime(3). A pointer to this structure should be passed as the third ioctl(2) argument.


Sets this RTC_zsingle_quotesz_s time to the time specified by the rtc_time structure pointed to by the third ioctl(2) argument. To set the RTC_zsingle_quotesz_s time the process must be privileged (i.e., have the CAP_SYS_TIME capability).


Read and set the alarm time, for RTCs that support alarms. The alarm interrupt must be separately enabled or disabled using the RTC_AIE_ON, RTC_AIE_OFF requests. The third ioctl(2) argument is a pointer to an rtc_time structure. Only the tm_sec, tm_min, and tm_hour fields of this structure are used.


Read and set the frequency for periodic interrupts, for RTCs that support periodic interrupts. The periodic interrupt must be separately enabled or disabled using the RTC_PIE_ON, RTC_PIE_OFF requests. The third ioctl(2) argument is an unsigned long * or an unsigned long, respectively. The value is the frequency in interrupts per second. The set of allowable frequencies is the multiples of two in the range 2 to 8192. Only a privileged process (i.e., one having the CAP_SYS_RESOURCE capability) can set frequencies above the value specified in /proc/sys/dev/rtc/max-user-freq. (This file contains the value 64 by default.)


Enable or disable the alarm interrupt, for RTCs that support alarms. The third ioctl(2) argument is ignored.


Enable or disable the interrupt on every clock update, for RTCs that support this once-per-second interrupt. The third ioctl(2) argument is ignored.


Enable or disable the periodic interrupt, for RTCs that support these periodic interrupts. The third ioctl(2) argument is ignored. Only a privileged process (i.e., one having the CAP_SYS_RESOURCE capability) can enable the periodic interrupt if the frequency is currently set above the value specified in /proc/sys/dev/rtc/max-user-freq.


Many RTCs encode the year in an 8-bit register which is either interpreted as an 8-bit binary number or as a BCD number. In both cases, the number is interpreted relative to this RTC_zsingle_quotesz_s Epoch. The RTC_zsingle_quotesz_s Epoch is initialized to 1900 on most systems but on Alpha and MIPS it might also be initialized to 1952, 1980, or 2000, depending on the value of an RTC register for the year. With some RTCs, these operations can be used to read or to set the RTC_zsingle_quotesz_s Epoch, respectively. The third ioctl(2) argument is an unsigned long * or an unsigned long, respectively, and the value returned (or assigned) is the Epoch. To set the RTC_zsingle_quotesz_s Epoch the process must be privileged (i.e., have the CAP_SYS_TIME capability).


Some RTCs support a more powerful alarm interface, using these ioctls to read or write the RTC_zsingle_quotesz_s alarm time (respectively) with this structure:

struct rtc_wkalrm {
  unsigned char   enabled;  
  unsigned char   pending;  
  struct rtc_time   time;  
  • The enabled flag is used to enable or disable the alarm interrupt, or to read its current status; when using these calls, RTC_AIE_ON and RTC_AIE_OFF are not used. The pending flag is used by RTC_WKALM_RD to report a pending interrupt (so it_zsingle_quotesz_s mostly useless on Linux, except when talking to the RTC managed by EFI firmware). The time field is as used with RTC_ALM_READ and RTC_ALM_SET except that the tm_mday, tm_mon, and tm_year fields are also valid. A pointer to this structure should be passed as the third ioctl(2) argument.


/dev/rtc, /dev/rtc0, /dev/rtc1, etc.

RTC special character device files.


status of the (first) RTC.


When the kernel_zsingle_quotesz_s system time is synchronized with an external reference using adjtimex(2) it will update a designated RTC periodically every 11 minutes. To do so, the kernel has to briefly turn off periodic interrupts; this might affect programs using that RTC.

An RTC_zsingle_quotesz_s Epoch has nothing to do with the POSIX Epoch which is used only for the system clock.

If the year according to the RTC_zsingle_quotesz_s Epoch and the year register is less than 1970 it is assumed to be 100 years later, that is, between 2000 and 2069.

Some RTCs support wildcard values in alarm fields, to support scenarios like periodic alarms at fifteen minutes after every hour, or on the first day of each month. Such usage is nonportable; portable user-space code expects only a single alarm interrupt, and will either disable or reinitialize the alarm after receiving it.

Some RTCs support periodic interrupts with periods that are multiples of a second rather than fractions of a second; multiple alarms; programmable output clock signals; nonvolatile memory; and other hardware capabilities that are not currently exposed by this API.


date(1), adjtimex(2), gettimeofday(2), settimeofday(2), stime(2), time(2), gmtime(3), time(7), hwclock(8)

Documentation/rtc.txt in the Linux kernel source tree


This page is part of release 4.16 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at−pages/.

Copyright 2002 Urs Thuermann (

This is free documentation; you can redistribute it and/or
modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of
the License, or (at your option) any later version.

The GNU General Public License_zsingle_quotesz_s references to object code
and executables are to be interpreted as the output of any
document formatting or typesetting system, including
intermediate and printed output.

This manual is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
GNU General Public License for more details.

You should have received a copy of the GNU General Public
License along with this manual; if not, see

$Id: rtc.4,v 1.4 2005/12/05 17:19:49 urs Exp $

2006-02-08 Various additions by mtk
2006-11-26 cleanup, cover the generic rtc framework; David Brownell